Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Tools/Maintenance

$519.99 - $639.99
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
$579.99
The SBK-1 is a professional level kit for installing and removing cartridge bearings in bicycle suspension pivots. A comprehensive set of 27 precision-machined hard-anodized guides enables compatibility with a wide range of bearing inner and outer diameters. Combined with our proven bearing press design, the SBK-1 quickly and easily pushes the old bearing out of the linkage and reinstalls the new bearing precisely and squarely. - Magnetic back plate for easy configuration and assembly - Organized in a convenient storage case Includes extractor cups/drifts for the following ODs: - 16mm - 17mm - 19mm - 20.6mm - 21mm - 22mm - 22.3mm - 24mm - 26mm - 28mm - 28.6mm - 30mm - 32mm - 35mm Includes extractor studs and pilots for bearings with the following IDs: - 8.5–9mm - 10mm - 12mm - 12.7mm - 15mm - 17mm - 20mm NOTE: For bearing extraction, the SBK-1 requires a minimum of 3mm of flat linkage structure outside the bearing to support the extractor cup/drift. For bearings without this flat structure, consider using the Park Tool SHX-1 Slide Hammer Bearing Extractor.
$549.99
The PRS-26 incorporates proven features from our other Team Issue stands to produce a strong, lightweight repair stand that's at home on-the-go or in the race pits. The sturdy tripod leg design folds and unfolds quickly and easily, and provides stability on any surface. The clamp is height-adjustable from 97 to 147 cm (38" to 58"), and can be positioned over one leg or between two legs to accommodate any bike. Precisely constructed from anodized 6063 T6 lightweight aluminum and durable composites, the PRS-26 is our lightest full-featured repair stand, and folds compactly for storage or transport. The PRS-26 is equipped with the time-tested 100-25D Micro-Adjust Clamp, the same design featured on our shop repair stands. The 100-25D features narrow clamping jaws to fit into tight areas or on short seat posts, and clamps nearly any tube from 23 to 76 mm (7/8" to 3"), including aero tubes and dropper posts. The cam-actuated adjustment system allows for quick entry, adjustment and exit. - Maximum weight capacity*: 36 kg (80 lbs.) - Clamp capacity: round and aero tubes from 22 to 76 mm (7/8" to 3") wide - Jaw width: 70 mm (2.75") - Height adjustable from 97 to 147 cm (38" to 58") - Base when open forms a triangle of 126 x 126 x 126 cm (49.6" x 49.6" x 49.6") - Weight: 5.7 kg (12.6 lbs.) - The PRS-26 uses the 100-25D Micro-Adjust Clamp - Replaceable jaw covers (part #1960) *NOTE: The maximum weight capacity of the PRS-26 assumes the bike's center of gravity is positioned directly below the clamp.
$549.99
The 791 Reamer Set reamer is used on the PF30 frame shells. The reamer is sized at 45.94mm. The 791 Reamer Set must used with the HTR-1 Head Tube Reamer and Facer, a 750.2 Centering Cone and the 690-XL Facer. The 791 set also includes a pilot that allows a facing-only option of the PF30 frame shell.
$549.99
Walk into the service area of any bike shop in the world, and odds are good you'll see a Park Tool Professional Wheel Truing Stand on the bench still the top choice of professional mechanics everywhere for over 40 years, and for good reason. With extra-tall uprights and wide calipers, the TS-2.3 is capable of accepting most wheels commonly found on road, mountain, BMX, and hybrid bicycles, including wheels with disc brakes, aero rims, and oversized MTB tires. Upright adjustment is controlled with an ergonomically-designed speed knob, which quickly adjusts the stand to accommodate any hub width in seconds. The sturdy uprights of the TS-2.3 feature integrated storage for the included thru-axle adapters, which allow for compatibility with thru-axle, quick release, and solid axle hubs without the use of additional parts or adapters. The TS-2.3 is constructed from durable powder-coated heavy-gauge steel and is manufactured, assembled, and calibrated in St. Paul, Minnesota. Strong, comfortable knobs and spring-loaded calipers and caliper arm ensure smooth, consistent operation, and the removable composite caliper tips protect painted rims and fragile materials. 100% adjustable and rebuildable for a lifetime of use. Wheel Capacity: - Maximum wheel size: Up to 29" + with or without tire - Maximum hub width: 200 mm (7.87") - Maximum rim width: 102 mm (4") - Hub compatibility: Accommodates quick release and solid axle hubs, also accommodates thru axle hubs using included TS-2TA.2 Thru Axle Adaptors Mounting Options: - Bolt to benchtop — mounting holes are 9.5 mm (3/8") in diameter and 200 mm (7.9") from center to center - Clamp in vise — base is 76 mm (3") deep - Install in TSB-2.2 Truing Stand Base
$539.99
Park Tool's Fork Threading Set is designed for cutting new threads and for chasing existing threads on fork columns that are not chromed. The FTS-1's expandable cutting dies are made from the highest quality high-speed steel for precision cutting and long life. The unique thread guide system used with the FTS-1 is specially designed to allow the metal chips and shavings that result during use to fall completely through the guide, preventing damage to the fork threads and the tool. The FTS-1 includes: • Die handles • 1" x 24 tpi cutting die (Part #606) • 1" cutting guide (Part #610) Accessory dies and guides are also available separately: • 1-1/8" x 26 die (Part #607) • 1-1/8" guide (Part #611) • 1-1/4" x 26 die (Part #608) • 1-1/4" guide (Part #612) Die handles fit all three sizes of dies and guides.
$529.99
Park's Bench-Mount Repair Stand easily bolts to any workbench and includes Park's shop-quality solid cast-aluminum Adjustable-Linkage Clamp that boasts durable, protective and replaceable vinyl jaw covers. The clamp holds seatposts and frames from an inch to 1 5/8 inches in diameter and there are slots for cables, too. Plus, this stand rotates 360 degrees for optimum bike positioning.
$529.99
The Deluxe Wall-Mount Repair Stand easily mounts to any post or wall stud. This shop-quality stand places the bike approximately 14.5 inches from the wall, so you'll have plenty of work space. The awesome clamp is Park's Adjustable Linkage model, which feature's replaceable rubber jaws; fits seatposts and frame tubes from 1 to 1 5/8-inch diameter; includes recesses for cable housing and rotates 360 degrees for optimum bike positioning. This great stand lets you work on your bikes just like a pro and is built to last.
$519.99
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
$510.00
To achieve maximum suspension performance, proper setup and tuning is essential. Go to www.rockshox.com/app for suggested air spring pressure and rebound damper settings for your fork. Go to www.sram.com/service for additional product and technical information. Air spring pressure and coil spring tables are available in the RockShox® Front Suspension Oil, Air, Coil, Token, and Specification documents. For a complete list of available coil springs and Bottomless Tokens™, consult the RockShox Spare Parts Catalog. Consult the RockShox service manual for your fork for complete disassembly and assembly procedures. Tuning suggestions are starting points. It may take trying various adjustments to find the settings that work best for each individual rider and trail condition. - Includes complete right-side internals
$510.00
To achieve maximum suspension performance, proper setup and tuning is essential. Go to www.rockshox.com/app for suggested air spring pressure and rebound damper settings for your fork. Go to www.sram.com/service for additional product and technical information. Air spring pressure and coil spring tables are available in the RockShox® Front Suspension Oil, Air, Coil, Token, and Specification documents. For a complete list of available coil springs and Bottomless Tokens™, consult the RockShox Spare Parts Catalog. Consult the RockShox service manual for your fork for complete disassembly and assembly procedures. Tuning suggestions are starting points. It may take trying various adjustments to find the settings that work best for each individual rider and trail condition. - Includes complete right-side internals
$499.99
Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.
$499.99
Perfect for taking to races and rides, the Portable Workbench is a bench that folds for easy transport and storage. It features a large work surface with specially sized slots, holes, and recesses and for holding tools, shop towels, lubes, beverages, etc. The folding steel legs provide a solid base for a toolbox and supplies, too.
$479.99
The Deluxe Wall-Mount Repair Stand easily mounts to any post or wall stud. This shop-quality stand places the bike approximately 14.5 inches from the wall, so you'll have plenty of work space. The awesome clamp is Park's Professional Micro-Adjust model, which features replaceable rubber jaws; fits seatposts and frame tubes from 7/8 to 3-inch diameter; includes recesses for cable housing and rotates 360 degrees for optimum bike positioning. This great stand lets you work on your bikes just like a pro and is built to last.
$449.99
Bundle includes qty 1 of the following: - Pressure Washer with all lances - Storage bag - Snow Foam Lance - Nano-Tech Bike Cleaner, 1L (900933-02) - Nano-Tech Cleaner Concentrate, 1L (901007-02) - Bike Protect, 500ml (901684-01) - Drivetrain Cleaner, 500ml (901101-01) - C3 Dry Lube, 120ml (900965-02) - Qty 2 Premium Microfiber Polishing Cloth (901555-01)
$433.99
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-3C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits all generations of PRS-2, PRS-3, and PRS-4 stands, and PRS-5 stands manufactured before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
$431.99
Park's HHP-2 accurately aligns and presses 1-, 1-1/8-, 1-1/4- and 1.5-inch headset cups into your frame's headtube. It features a quick-release design for fast tool installation and removal, extra-long handles for superior leverage and stepped bushings for precise cup alignment. This versatile tool also presses cartridge bearings and cups into one-piece bottom bracket shells and holds fixed-cup wrenches in place when removing or installing adjustable-type bottom brackets.
$430.00
Many athletes are fortunate enough to be able to ride nearly anything. For those that are sensitive to bike fit though, replicating fit to a new bike or confirming fit after travel can be a challenge involving lots of trial and error. This set of tools allows accurate and repeatable measurements for saddle height, angle and setback. The accuracy and repeatable measurements also serve as a base to make adjustments to fit. -The magnetic saddle height bullets ensure you get an accurate center at the BB by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate. -Two reference marks on the saddle plate means you can pull a measurement to the exact same spot relative to the nose of the saddle every time. This gives you accuracy down to a single millimeter. -The front of the saddle plate is engraved with a ruler, to allow you to calculate saddle setback at the saddle. This allows you to drop the plumb bob off the side of the bike and clear all of the bottle cages. -The wide plate has ample room to mount a level, protractor or smart phone for adjusting the angle of the saddle. This is particularly helpful for non traditional saddles like SMP and Adamo.
$420.99
- Crank Saver—Pedal thread repair and insert kit - Includes: left and right reaming tap 5/8x24 TPI, 10 pedal thread inserts for left crank arm, 10 pedal thread inserts for right crank arm, metal box with cut out SOS foam trays.
$419.99
Park's Dial Indicator Gauge Set mounts to their TS-2 or TS-2.2 Truing Stand (sold separately). The set makes it easy to view and correct a wheel's lateral and radial run-out within a tolerance of .01mm. Compared to going by the gap between the truing stand pointer and rim, having gauges that put a number on the clearance makes wheel truing easier and more accurate.
$419.99
A compact and lightweight foldable workstand with unique 4-way adjustment and solid base for home shop, race day or events. - Holder: Accepts bikes with quick-release fork or 12 x 100mm, 15 x 100 / 110mm, 20 x 110mm thru-axle forks - Holder Height: 85cm - 145cm / 33" - 57" - Folding: Three QR clamps - Base: HD folding 6061-T6 tubes - Material: 6061-T6 tubes / aluminum - Max Load: 18kg / 39.7lb - Weight: 4.9kg / 10.8lb - Height adjustable - 90 degree up/down angle adjustable - Fore and aft adjustable, 360 degree rotatable - Optional Tool Tray - Optional carry bag Size - 86 x 25 x 16cm / 33.9" x 9.8" x 6.3" (Folded) - 120cm / 47.2" (Base Diameter)
$407.00
To achieve maximum suspension performance, proper setup and tuning is essential. Go to www.rockshox.com/app for suggested air spring pressure and rebound damper settings for your fork. Go to www.sram.com/service for additional product and technical information. Air spring pressure and coil spring tables are available in the RockShox® Front Suspension Oil, Air, Coil, Token, and Specification documents. For a complete list of available coil springs and Bottomless Tokens™, consult the RockShox Spare Parts Catalog. Consult the RockShox service manual for your fork for complete disassembly and assembly procedures. Tuning suggestions are starting points. It may take trying various adjustments to find the settings that work best for each individual rider and trail condition. - Includes complete right-side internals
$389.99 $409.99 5% Off
"A full-featured bicycle workstand designed and built for the home mechanic. The PCS-10.3 includes Park Tool's tried and true cam-actuated micro-adjustable clamp design for quick one-handed entry and exit, as well as a quick-release height adjustment lever for easy, secure adjustment. Features 18"" (460 mm) of height adjustment and 360 degrees of clamp rotation, positioning all parts of the bike within reach for any mechanic whether seated or standing. The stand's all-steel construction with teardrop-shaped tubing ensures maximum rigidity and stability, with tubular support braces, a locking support yoke, and upgraded internals for extra dependability. The PCS-10.3 is able to hold up to 80 lbs. (36 kg), which allows for compatibility with virtually all two-wheeled pedal-driven bicycles, including fat bikes and most e-bikes. The PCS-10.3 features an integrated height-adjustable parts tray, as well as accessory ports for the Park Tool #106 Work Tray or PTH-1 Paper Towel Holder (both sold separately), so your tools and small parts are always within reach. Quickly folds down for storage and transport with a smooth-operating leg support system that pulls both legs up in one simple motion. The PCS-10.3 is the perfect way to upgrade your home shop—a stable way to hold nearly any bike off the ground for adjustments, cleaning and repair. NOTE: The maximum weight capacity of the PCS-10.3 assumes the weight is centered below the clamp and between the legs.? - Cam-actuated micro-adjustable clamp fits 7/8"" to 3"" (22 mm–76 mm) diameter tubes and seat posts of any shape and material, including aero posts and dropper posts - Narrow clamping jaws (2.7""/70 mm) fit into tight areas or on short seat posts - Rubber saddle pad allows bikes to be hung by the saddle for quick adjustment or storage - Durable, textured powder coat finish - Integrated height-adjustable parts tray - Height adjustment collar features accessory ports for compatibility with the #106 Work Tray or PTH-1 Paper Towel Holder (both sold separately) - Maximum weight capacity*: 80 lbs. (36 kg) - Height adjustable from 39"" to 57"" (990 mm–1450 mm) using convenient quick-release lever - Base when open forms a triangle of 36"" x 36"" x 48"" (920 mm x 920 mm x 1210 mm) - Folds down to 45"" x 14.5"" (1140 mm x 370 mm) - Weight: 16 lbs. (7.2 kg)"
$379.99
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
$311.99 - $379.99
After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments
$374.99
- Hub bearing press set with 10 guides - For ID 8-20mm
$371.00
The lightest production damper. Ever. Performance packed with a rock-solid lockout to power up climbs and smash through sprint finishes. - Every detail machined and optimized to save on weight and maximize your performance - Factory tuned compression (in open position) provides the highest level of XC performance, precision and control - Maximum efficiency with a rock-solid lockout
$363.99
Click-Torque wrench in the unmistakable, robust Wera design with high accuracy. Easy setting and saving of the default value. The audible and tactile clicks on reaching the scale values also facilitate the safe setting of the desired torque value. For right-hand use (clockwise torque control) and with 45-tooth reversible ratchet mechanism. - With 1/4" square drive, reversible ratchet, 45 teeth - Easy setting and saving of the desired torque value with audible and tactile clicks when reaching the scale values - Audible and tactile release mechanism when the set torque value is reached - Measuring range: 2.5-25 Nm; Precise to +/- 4% - Designed with ergonomic 2-component handle suitable for right-hand use
$359.99
The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.
$346.00
With a 15mm box end on one end and a custom 6 and 8 millimeter swivel bit on the opposite end, it's the only pedal wrench you'll ever need. Perfect to keep at the fit station, on the sales floor, and at the tool bench. The shop version of the tool gets an extra 6" (15cm) of leverage over the team issue for an overall length of 18 inches. Great for removing those stubborn pedals. - Durable black Cerakote finish - Made in Bend, Oregon