Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Parts & Accessories

Crank Brothers Highline Sticker Kit
$10.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
Crank Brothers Candy 2/3 Traction Pads - 2017+
$12.99
Polyurethane pads with diamond plate traction pattern allow riders to customize their pedals for a perfect interface with any shoe. - Kit includes eight 1mm traction pads and eight 2mm traction pads
Crank Brothers Tread Contact Sleeves
$14.59
Crank Brothers' Tread Contact Sleeves shim the area between the pedal and your shoes' tread so there is no rocking or play when you're clipped in. They provide a solid platform to put down all your power! They work with either your Eggbeaters or Candy pedals, and each includes 1mm, 2mm, and 3mm shims.
Crank Brothers Shoe Shields
$14.99
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes.
Crank Brothers 5050 Pin Kit
$19.99
Crank Brothers' 5050 Pin Kit includes fifty 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
Crank Brothers Pedal Rebuild Kit
$21.99
Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.
Crank Brothers Traction Pads for Mallet E
$22.99
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present
Crank Brothers Pedal Refresh Kit - Doubleshot
$32.99
A revolution in performance and reliability. - The kit includes premium internal components: - Inner spindle seal x 2 - Outer spindle seal x 2 - Inner Igus solid bearing x 2 - Outer Enduro cartridge bearing x 2 - Spindle nut x 2 - Outer bearing carrier x 2 - Compatibility: Doubleshot (2016), Doubleshot 2 (2017+), Soubleshot 3 (2017+)
Crank Brothers Easy Release Cleat Kit
$34.99
Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals
Crank Brothers Premium MTB Cleats
$35.99
Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees
Crank Brothers Pedal Refresh Kit
$36.99
Your pedals like to be pampered. The Crank Brothers Pedal Refresh Kit gives you everything you need to keep them happy. Pedal Refresh Kit includes: -Enduro catridge bearings - Igus LL-glide bearings - Double seal system (internal and external seals) - Hex alloy end caps - O-rings - Nuts - Sleeve bushings - Bearing removal tool Compatible with the following pedals (2010-present): - Eggbeaters - Candys - Mallets - 5050s
Crank Brothers Zero Float Cleats
$36.99
Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees
Crank Brothers Quattro 3-Hole Cleats
$39.99
Crank Brothers' Quattro 3-hole cleats let you use Crank Bros. pedals with your road shoes. The cleat and walking plate mount directly to shoes that use a traditional 3-hole mounting setup. - Weight (pair): 86 grams - Shoe compatibility: LOOK/SPD-SL - Release angle: 15 or 20 degrees
Crank Brothers Long Spindle Kit
$68.99
Widen your Q-factor to 57mm. - Long spindles are 5mm longer than standard. - The kit includes: 1 pair long spindles + refresh kit (Enduro cartridge bearings, igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double shot, model years 2010-present - Weight: 112g per pair - Spindle material: forged SCM 435 chromoly steel - Q-factor: 57mm
Crank Brothers Titanium Spindle Kit
$189.99
The ultimate weight-saving upgrade.  - The kit includes: 1 pair titanium spindles + refresh kit (Enduro cartridge bearings, Igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double Shot, model years 2010-present - Weight: 60g per pair - Spindle material: 6al/4v titanium - Max. rider weight: 200lb/90kg - Q-factor: 52 mm
DMR Vault Flip Pins
$23.99
- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove
Delta Foot Fenders
$15.99
- Strapless design is easy to engage without fully committing to the pedal - No special shoes required - Improves pedaling efficiency - Molded from unbreakable nylon - Please make sure your pedals have visible mounting points or a removable reflector for mounting prior to purchase - Includes mounting hardware. Note: metal plate may not be required during installation.
Eclypse 98A Cleats
$21.99
- Compatible with all Shimano SPD type pedals - 4 degrees of float - Sold in pairs with hardware - Compatible with Multisport 4 pedal
Ergon TP1 Pedal Cleat Tool
$39.99
The Ergon TP1 Pedal Cleat Tool is the first tool for precisely and easily adjusting cycling shoes cleats. The ergonomically correct position of the feet on the pedals plays a crucial role in injury prevention and is also important for maximizing both performance and comfort.
Fyxation Gates Pedal Strap Set
$62.99
- Wide and durable, 2-inch reinforced nylon seat-belt webbing upper strap with a smooth metal sizing buckle and 1-inch dual/lower run-through straps for retention control and comfort - Minimalist styling and extra-Long top strap will adjust to fit most uses, While stiffer lower straps help retain shape for easy in/out - Fits gates and other platform pedals with larger side-port openings (Sold as a set for 1 pair/bike's worth of pedals)
Garmin Vector Cleats
$39.99
Don't let pedal issues keep you from training. This replacement pair of anti-slip LOOK Kéo-compatible cleats with 6 degree or 0 degree float (depending on the version selected) will keep your Vector pedals turning and your training on track. - Compatible with all Garmin Vector Pedals
LOOK Keo Cleat Covers
$15.99
The Keo Cover protects your cleats while walking. They are compatible with all Keo Grip cleats and Keo Cleats. – Cleats protection – Anti-slip – Compatible with all cleats
LOOK X-Track Cleats
$24.99
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK cleats provide 6° of float and 13° angle of disengagement and allow for unidirectional release only.
LOOK Keo Cleats
$29.99 - $32.99
The KEO standard cleat is recognized in the cycling world for its minimal weight and compact cleat/pedal system design. The memory positioner is a major advantage when changing your cleats allowing you to get the exact same position upon replacement. Available in multiple float options, with corresponding colors. The Grey Cleats offer 4.5 degrees of float.
LOOK X-Track Easy Cleats
$29.99
X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide 6° of float and 13° angle of disengagement and allow for multidirectional release.
LOOK Keo Grip Cleats
$41.99
Look's Keo Grip Cleats feature special anti-slip surfaces on the bottom that improve traction while walking. They are made of polyamide nylon for easy entry/exit, efficient pedaling, and durability. And, there are wear indicators that tell you when it's time for new cleats. The Keo Grip cleats are available with three different amounts of lateral float: 4.5-degree (gray), 9-degrees (red), and fixed float (black). - These cleats are compatible with Look Keo pedals (sold separately). - These cleats use the Look/SPD-SL bolt pattern.
Look S-Track Cages
$44.99
Look's S-Track Cages increase the surface area of Look's S-Track pedals, making them perfect for enduro and all-mountain riders, off-road touring fans, or anyone who rides clipped in but appreciates the stability of a platform. They give you a wide, anti-slip platform to keep your feet on the pedals even when you're not clipped in. - Compatible with Look S-Track pedals (sold separately)
Look S-Track Sauser Cage
$49.99
Look's S-Track Sauser Cage increase the surface area of Look's S-Track pedals, making them perfect for enduro and all-mountain riders, off-road touring fans, or anyone who rides clipped in but appreciates the stability of a platform. They give you a wide, anti-slip platform to keep your feet on the pedals even when you're not clipped in. - Adaptable to all of the S-Track range (sold separately) - 25g
Look S-Track Enduro Cage
$119.99
Look's S-Track Enduro Cage increase the surface area of Look's S-Track pedals, making them perfect for enduro and all-mountain riders, off-road touring fans, or anyone who rides clipped in but appreciates the stability of a platform. Constructed from lightweight aluminum, they give you a wide, anti-slip platform to keep your feet on the pedals even when you're not clipped in. - Adaptable to all of the S-Track range (sold separately) - 60g
Shimano SM-SH51 SPD Cleat Set
$26.99
Shimano's SPD cleats are perfect for all your SPD-compatible pedals. If your entry and exit isn't what it used to be, a cleat replacement is just what the bike doctor ordered.
Page 1 of 2 Next page